GPRS Sniffing Tutorial

git clone git://git.osmocom.org/osmocom-bb.git
git clone git://git.osmocom.org/libosmocore.git
git clone git://git.srlabs.de/gprsdecode.git
wget http://srlabs.de/dl/gprs_multi.patch

wget http://gnuarm.com/bu-2.15_gcc-3.4.3-c-c++-java_nl-1.12.0_gi-6.1.tar.bz2
tar xf bu-2.15_gcc-3.4.3-c-c++-java_nl-1.12.0_gi-6.1.tar.bz2

cd ~/gprs_sniffer/libosmocore
autoreconf -i
./configure
make
sudo make install

cd ~/gprs_sniffer/gprsdecode
make

cd ~/gprs_sniffer/osmocom-bb
git checkout origin/sylvain/burst_ind
git checkout d1cb8ea9b784c7acbafbb2fdcedbdf4655c2f6f5
patch -p1 < ~/gprs_sniffer/gprs_multi.patch

cd src
export PATH=$PATH:~/gprs_sniffer/gnuarm-3.4.3/bin
make

# Conect Motorola phone with USB cable
cd ~/gprs_sniffer/osmocom-bb/src
./host/osmocon/osmocon -m c123xor -p /dev/ttyUSB0 ./target/firmware/board/compal_e88/layer1.compalram.bin
# Switch on Motorola phone

cd ~/gprs_sniffer/osmocom-bb/src
./host/layer23/src/misc/cell_log

# look for active networks in the output:
cell_log.c:334 Sync ARFCN 29 (rxlev -52, 289 syncs left)
cell_log.c:190 Cell: ARFCN=29 MCC=222 MNC=01 (Italy, TIM)
# in this case, network is TIM, and ARFCN is 29
# kill cell_log with ctrl-c, and rerun with correct ARFCN:
./host/layer23/src/misc/layer23 -a 29

# Data channel assignments look like this
layer3.c:243 GSM48 IMM ASS (ra=0x72, chan_nr=0x0a, HSN=44, MAIO=0,
TS=2, SS=0, TSC=0)l1ctl.c:506 Tx Dedic.Mode Est Req (maio=0,
hsn=44, chan_nr=0x0a)

# Red lines indicate signal strength
# In this case 3 out of 4 slots are used:
l1ctl.c:261 BURST IND: @(2064231 = 1556/13/06) ( -50 dBm, SNR 255)
l1ctl.c:261 BURST IND: @(2064231 = 1556/13/06) ( -50 dBm, SNR 1)
l1ctl.c:261 BURST IND: @(2064231 = 1556/13/06) ( -50 dBm, SNR 255)
l1ctl.c:261 BURST IND: @(2064231 = 1556/13/06) ( -50 dBm, SNR 255)

# wait for session end or kill with ctrl-c
# A file like "bursts_20110821_1648_29_2094723_0a.dat" is produced

# Start Wireshark, capturing on interface "lo"
~/gprs_sniffer/gprsdecode/gprsdecode bursts_20110721_1648_29_2094723_0a.dat

wget http://srlabs.de/dl/gprs_262_80_0001_0000_20110710_2251_875_494777_0f.dat
~/gprs_sniffer/gprsdecode/gprsdecode gprs_262_80_0001_0000_20110710_2251_875_494777_0f.dat
wget http://srlabs.de/dl/gprs_262_80_0001_0000_20110710_2252_875_514147_0f.dat
~/gprs_sniffer/gprsdecode/gprsdecode gprs_262_80_0001_0000_20110710_2252_875_514147_0f.dat

svn co http://anonsvn.wireshark.org/wireshark/trunk wireshark
cd wireshark
./autogen.sh
./configure
make
sudo make install

# the default firmware captures 4 downlink slots,
# for uplink you need to compile a different firmware.
# open "osmocom-bb/src/target/firmware/layer1/prim_sniff.c"
# at line 288, modify #if 1 to 0
# go back to ‘Compile and install libosmocore‘