首页 > 其他 > 详细

Frame Relay - 简介及基本配置

时间:2014-05-09 14:43:30      阅读:436      评论:0      收藏:0      [点我收藏+]

Frame Relay现在越来越不流行了,不过在过去的设计中被广泛应用。

所以工作上还是能经常见到的, 这篇博文从二层简单总结下FR的一些概念


在介绍Frame Relay之前,先了解下广播介质和非广播介质的区别:


Broadcast Media (广播介质): Ethernet 、 Token-Ring、FDDI

特点:

  • 源可以同时向所有连接(二层)目的地址通话
  • 简化了三层到二层的解析

Non-Broadcast Multi Access (NBMA): Frame Relay、ISDN、ATM etc。

特点:

  • 源不能同时和二层相连的所有目的地址通话
  • 三层的广播通过二层重复的单播实现 (pseudo-broadcast)

========三层到二层的地址解析对比=======

广播介质的三层地址解析:远程二层MAC地址和远程三层地址绑定

 - IPv4 Adress Resolution Protocol ( ARP)

  • 广播请求 - 谁知道1.1.1.1的MAC地址
  • 单播回复 - 我的MAC是abcd.abcd.abcd

广播介质的三层地址解析:远程或本地的二层MAC地址和远程三层地址绑定

  • 本地FR DLCI和远程IPv4地址绑定
  • 远端ISDN电话和原电IPX地址绑定

- 反向ARP用解析远程三层地址到本地二层地址

- 只有直接相连的设备可以进行解析


NBMA 端口类型:

多点接口 - 可连接多个二层链路 & 需要三层到二层的解析 (FR & ATM main interface)

单点接口 - 连接一个二层链路 & 不需要三层到二层解析 (PPP link, FR p2p subinterface) 


======================================

1. FR 简介

应用了NBMA - 也就意味着潜在存在三层到二层解析问题

DLCI - Data link Connection Identifier (数字链路识别码)

  • 二层寻址
  • DLCI本地有效

LMI - Local Management Interface

  • DTE or DCE 通讯
  • 汇报虚拟链路的状态

2. FR LMI 配置
开启FR
 - encapsulation frame-relay
LMI的类型 ( 自动侦测)
 - frame-relay lmi-type 【cisco | ansi | q933a】
- show frame-relay lmi
验证虚拟链接VC状态
- show frame-relay pvc
状态种类:
- active (E2E是好的,至少router 到 switch是ok的)
- inactive (中途出了问题)
- deleted ( 路由器试图用一些参数但是FR交换机不支持,配置错误等)
- static (LMI is disabled,用于back to back FR)

3. FR 地址解析
- 多点端口需要三层到二层解析: 想要发包到IP a.b.c.d需要哪个DLCI ?
- 解析的种类
  • 动态解析通过反向ARP请求 (inverse ARP)
  • 静态解析通过命令frame-relay map
- 验证: sh frame-relay map

=======
FR inverse ARP
- 当配置了FR支持的协议,反向ARP自动开启
- 请求会在端口配置的所有链路上发出
  • 反向APR请求发送可以disable - no frame-relay inverse arp [protocol] [dlci]
  • 回复不能被disable (这是个潜在的问题)
- 自动包括了对广播的支持

FR static Mapping
- 手动把本地的二层地址和远程的三层地址绑定
  • frame-relay map [protocol] [address] dlci [broadcast]
  • 和静态ARP的逻辑一样
- 静态配置会覆盖动态配置
- 想支持广播的话需要手动配置
========

路由器的Auto-install和Frame Relay可能引入问题:
 - 如果在NVRAM里没有配置文件,路由器会侦测端口的封装模式和发送地址请求
LAN - DHCP
HDLC - SLARP
FR - BOOTP
- 当地址配置过后,路由器就会试图通过TFTP拿到配置

FR在这里出现的问题在第四步:
  1. 侦测封装
  2. 通过DLCI学习LMI
  3. 给所有DLCIs发送BOOTP
  4. 如果请求失败了,会自动配置0.0.0.0 mapping

  • 这可能破坏之后的路由配置
  • 解决方法就是save config and reload
=================
最后要提的是点到点端口

- 一个端口对一条二层链路
- 不需要三层到二层的解析,只需要配置链路号 - frame-relay interface-dlci [dlci]
- 更倾向于点到点配置(可以避免三层以上配置问题)


================
思科官方文档 - 基本配置

An interface is by default a "multipoint" interface so, frame-relay inverse-arp is on (for point-to-point, there is no Inverse ARP). IP split horizon checking is disabled by default for Frame Relay encapsulation, so routing updates come in and out the same interface. The routers learn the data-link connection identifiers (DLCIs) they need to use from the Frame Relay switch via LMI updates. The routers then Inverse ARP for the remote IP address and create a mapping of local DLCIs and their associated remote IP addresses.


bubuko.com,布布扣


Spicey
Spicey#show running-config
Building configuration...

Current configuration : 1705 bytes
!
version 12.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Spicey
!
!
!
interface Ethernet0
 ip address 124.124.124.1 255.255.255.0
!
interface Serial0
 ip address 3.1.3.1 255.255.255.0
 encapsulation frame-relay
 frame-relay interface-dlci 140
!
!
router rip
 network 3.0.0.0
 network 124.0.0.0
!
line con 0
 exec-timeout 0 0
 transport input none
line aux 0
line vty 0 4
 login
!
end
Prasit
Prasit#show running-config
Building configuration...
Current configuration : 1499 bytes
!
version 12.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Prasit
!
!
!
interface Ethernet0
 ip address 123.123.123.1 255.255.255.0
!
!
interface Serial1
 ip address 3.1.3.2 255.255.255.0
 encapsulation frame-relay
 frame-relay interface-dlci 150
!
!
router rip
 network 3.0.0.0
 network 123.0.0.0
!
!
!
line con 0
 exec-timeout 0 0
 transport input none
line aux 0
line vty 0 4
 login
!
end


验证

  • show frame-relay map

  • show frame-relay pvc

  • show frame-relay lmi

  • ping <device name>

  • show ip route

Spicey#show frame-relay map
Serial0 (up): ip 3.1.3.2 dlci 140(0x8C,0x20C0), dynamic,
              broadcast,, status defined, active

Spicey#show frame-relay pvc
PVC Statistics for interface Serial0 (Frame Relay DTE)
              Active     Inactive      Deleted       Static
  Local          1            0            0            0
  Switched       0            0            0            0
  Unused         0            0            0            0

DLCI = 140, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0
  input pkts 83            output pkts 87           in bytes 8144      
  out bytes 8408           dropped pkts 0           in FECN pkts0         
  in BECN pkts 0           out FECN pkts 0          out BECN pkts0         
  in DE pkts 0             out DE pkts 0         
  out bcast pkts 41         out bcast bytes 3652      
  pvc create time 01:31:50, last time pvc status changed 01:28:28
Spicey#show frame-relay lmi
LMI Statistics for interface Serial0 (Frame Relay DTE) LMI TYPE = CISCO
  Invalid Unnumbered info 0             Invalid Prot Disc 0
  Invalid dummy Call Ref 0              Invalid Msg Type 0
  Invalid Status Message 0              Invalid Lock Shift 0
  Invalid Information ID 0              Invalid Report IE Len 0
  Invalid Report Request 0              Invalid Keep IE Len 0
  Num Status Enq. Sent 550              Num Status msgs Rcvd 552
  Num Update Status Rcvd 0              Num Status Timeouts 0
Spicey#ping 123.123.123.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 123.123.123.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/40 ms
Spicey#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS
inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route
 
Gateway of last resort is not set
     3.0.0.0/24 is subnetted, 1 subnets
C       3.1.3.0 is directly connected, Serial0
     124.0.0.0/24 is subnetted, 1 subnets
C       124.124.124.0 is directly connected, Ethernet0
R    123.0.0.0/8 [120/1] via 3.1.3.2, 00:00:08, Serial0

Prasit#show frame-relay map
Serial1 (up): ip 3.1.3.1 dlci 150(0x96,0x2460), dynamic,
              broadcast,, status defined, active

Prasit#show frame-relay pvc
PVC Statistics for interface Serial1 (Frame Relay DTE)
              Active     Inactive      Deleted       Static
  Local          1            0            0            0
  Switched       0            0            0            0
  Unused         0            0            0            0
DLCI = 150, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1
  input pkts 87            output pkts 83           in bytes 8408      
  out bytes 8144           dropped pkts 0           in FECN pkts 0         
  in BECN pkts 0           out FECN pkts 0          out BECN pkts 0         
  in DE pkts 0             out DE pkts 0         
  out bcast pkts 38         out bcast bytes 3464      
  pvc create time 01:34:29, last time pvc status changed 01:28:05

Prasit#show frame-relay lmi
LMI Statistics for interface Serial1 (Frame Relay DTE) LMI TYPE = CISCO
  Invalid Unnumbered info 0             Invalid Prot Disc 0
  Invalid dummy Call Ref 0              Invalid Msg Type 0
  Invalid Status Message 0              Invalid Lock Shift 0
  Invalid Information ID 0              Invalid Report IE Len 0
  Invalid Report Request 0              Invalid Keep IE Len 0
  Num Status Enq. Sent 569              Num Status msgs Rcvd 570
  Num Update Status Rcvd 0              Num Status Timeouts 0

Prasit#ping 124.124.124.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 124.124.124.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 36/36/36 ms
Prasit#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS
inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route
Gateway of last resort is not set
     3.0.0.0/24 is subnetted, 1 subnets
C       3.1.3.0 is directly connected, Serial1
R    124.0.0.0/8 [120/1] via 3.1.3.1, 00:00:19, Serial1
     123.0.0.0/24 is subnetted, 1 subnets
C       123.123.123.0 is directly connected, Ethernet0

参考资料:

Comprehensive Guide to Configuring and Troubleshooting Frame Relay


Frame Relay - 简介及基本配置,布布扣,bubuko.com

Frame Relay - 简介及基本配置

原文:http://blog.csdn.net/ziyuanzhao/article/details/25300803

(0)
(0)
   
举报
评论 一句话评论(0
关于我们 - 联系我们 - 留言反馈 - 联系我们:wmxa8@hotmail.com
© 2014 bubuko.com 版权所有
打开技术之扣,分享程序人生!