A robot has been programmed to follow the instructions in its path. Instructions for the next direction the robot is to move are laid down in a grid. The possible instructions are 

N north (up the page)
S south (down the page)
E east (to the right on the page)
W west (to the left on the page)

For example, suppose the robot starts on the north (top) side of Grid 1 and starts south (down). The path the robot follows is shown. The robot goes through 10 instructions in the grid before leaving the grid.

Compare what happens in Grid 2: the robot goes through 3 instructions only once, and then starts a loop through 8 instructions, and never exits.

You are to write a program that determines how long it takes a robot to get out of the grid or how the robot loops around.

There will be one or more grids for robots to navigate. The data for each is in the following form. On the first line are three integers separated by blanks: the number of rows in the grid, the number of columns in the grid, and the number of the column in which the robot enters from the north. The possible entry columns are numbered starting with one at the left. Then come the rows of the direction instructions. Each grid will have at least one and at most 10 rows and columns of instructions. The lines of instructions contain only the characters N, S, E, or W with no blanks. The end of input is indicated by a row containing 0 0 0.

For each grid in the input there is one line of output. Either the robot follows a certain number of instructions and exits the grid on any one the four sides or else the robot follows the instructions on a certain number of locations once, and then the instructions on some number of locations repeatedly. The sample input below corresponds to the two grids above and illustrates the two forms of output. The word "step" is always immediately followed by "(s)" whether or not the number before it is 1.

3 6 5
NEESWE
WWWESS
SNWWWW
4 5 1
SESWE
EESNW
NWEEN
EWSEN
0 0 

10 step(s) to exit
3 step(s) before a loop of 8 step(s)


模拟题，给定一个操作矩阵，N S W E 分别代表向上，下，左，右移动 给定一个机器人，机器人总是从最顶层开始，列坐标题目会给出，你的任务是判断几步之后机器人会走出这个矩阵（有可能永远也走不出，因为可能会形成一个环）我们虚拟一个墙，就是存字符的时候让它从下标1开始，而在矩阵外层套上一层别的字符，与题目中那4个字符不相同就可以，用来判断机器人是否走出矩阵，然后模拟操作就可以了，注意判断是否形成环，可以设一个数组vis[][]，初始化为0，代表所有的子符都没访问过，然后访问过就置为1，当判断到一个字符访问过2次时，说明有环，退出来继续操作就可以了（应该不难想）
#include <cstdio>
#include <iostream>
#include <cstring>
#include <cstdlib>
#include <cctype>
#include <algorithm>
#include <vector>
using namespace std;
bool vis[110][110];
char map[110][110];
int i,j;
char bfs(char x)
{
	if(x=='N')
		i--;
	else if(x=='S')
	    i++;
	else if(x=='E')
	    j++;
	else if(x=='W')
		j--;
	return map[i][j];
}
int main()
{
    int m,n,start;char next;
	while(cin>>m>>n>>start)
	{
		if(!m&&!n&&!start)break;
		memset(map,'a',sizeof(map));
		memset(vis,0,sizeof(vis));
		for(i=1;i<=m;i++)
			for(j=1;j<=n;j++)
			cin>>map[i][j];
		i=1;j=start;
		int cnt=1;vis[i][j]=1;
		next=map[i][j];
		while((next=bfs(next))!='a')
		{
			if(!vis[i][j])
			{cnt++;vis[i][j]=1;}
			else
			break;

		}
		vis[i][j]=0;int num=1;
		next=map[i][j];
		while((next=bfs(next))!='a')
		{
			if(vis[i][j])
		    num++;
			else
		    break;

		}
		if(num>1)
			cout<<cnt-num<<" step(s) before a loop of "<<num<<" step(s)"<<endl;
		else
			cout<<cnt<<" step(s) to exit"<<endl;
	}
	return 0;
}