OSPF协议的配置

1.在R1,R2,R3上配置接口ip

<r1>system-view
[r1]interface GigabitEthernet 0/0/0
[r1-GigabitEthernet0/0/0]ip address 10.1.1.1 24

<r2>system-view
[r2]interface GigabitEthernet 0/0/0
[r2-GigabitEthernet0/0/0]ip address 10.1.1.2 24
[r2-GigabitEthernet0/0/0]quit
[r2]interface GigabitEthernet 0/0/1
[r2-GigabitEthernet0/0/1]ip address 20.1.1.1 24

[r3]interface GigabitEthernet 0/0/1
[r3-GigabitEthernet0/0/1]ip address 20.1.1.2 24

2..在R1,R2,R3上配置OSPF协议

[R1]ospf 100
[R1-ospf-100]area 0
[R1-ospf-100-area-0.0.0.0]network 10.1.1.0 0.0.0.255
[R1-ospf-100-area-0.0.0.0]quit

[R2]ospf 100
[R2-ospf-100]area 0
[R2-ospf-100-area-0.0.0.0]network 10.1.1.0 0.0.0.255
[R2-ospf-100-area-0.0.0.0]network 20.1.1.0 0.0.0.255
[R2-ospf-100-area-0.0.0.0]quit

[R3]ospf 100
[R3-ospf-100]area 0
[R3-ospf-100-area-0.0.0.0]network 20.1.1.0 0.0.0.255
[R3-ospf-100-area-0.0.0.0]quit

查看OSPF邻居
[R3]display ospf peer

查看OSPF路由
[R3]display ip routing-table

二.修改修改OSPF的RID

[R1]ospf 100 router-id 1.1.1.1
RID修改后不会立即生效，需要重启OSPF进程新的RID才会生效）

重启OSPF进程：
<R1>reset ospf process
Warning: The OSPF process will be reset. Continue? [Y/N]:y

三.修改基准带宽

1.在R1，R2,R3上修改基准带宽
[R1]ospf 100
[R1-ospf-100]bandwidth-reference 10000

[R2]ospf 100
[R2-ospf-100]bandwidth-reference 10000

[R3]ospf 100
[R3-ospf-100]bandwidth-reference 10000

四.OSPF静默接口

1.设置OSPF静默接口：
[R2]ospf 100
[R2-ospf-100]silent-interface g0/0/1

五.修改OSPF计时器

1.在R1,R2上修改计时器
[R1]int g0/0/0
[R1-GigabitEthernet0/0/0]ospf timer hello 20
[R1-GigabitEthernet0/0/0]ospf timer dead 60

[R2]int g0/0/0
[R2-GigabitEthernet0/0/0]ospf timer hello 20
[R2-GigabitEthernet0/0/0]ospf timer dead 60

OSPF要求hello时间，dead时间邻居之间要一样，所以一改就得改两个

六.修改OSPF的DR,BDR角色

1.在R2上修改OSPF的DR接口优先级
[R2]int g0/0/0
[R2-GigabitEthernet0/0/0]ospf dr-priority 0

七.OSPF认证

1.在R1上配置OSPF接口认证
[R1]int g0/0/0
[R1-GigabitEthernet0/0/0]ospf authentication-mode md5 1 cipher huawei

2.在R2上配置OSPF区域认证
[R2]ospf 100
[R2-ospf-100]area 0
[R2-ospf-100-area-0.0.0.0]authentication-mode md5 1 cipher huawei

OSPF协议的配置

原文：https://blog.51cto.com/13212728/2517156