C:\Program Files\Atmel\Atmel Studio 6.1\atbackend\atprogram.exe
No command specified.
Atmel Studio Command Line Interface
Copyright (C)
2013 Atmel Corporation.
Usage: atprogram [options] <command> [arguments] [<command> [arguments] ...]
-t --tool <arg> Tool name: avrdragon, avrispmk2, avrone,
jtagice3,jtagicemkii, qt600, stk500, stk600, samice or edbg.
-s
--serialnumber <arg> The programmer/debugger serialnumber. Must
be specified when more than one debugger is connected.
-c
--comport <arg> The com port to use for the
programmer/debugger. e.g. -c COM1 or -c 1
-i --interface <arg>
Physical interface: aWire, debugWIRE, HVPP, HVSP, ISP, JTAG, PDI, TPI
or SWD.
-d --device <arg> Device name. E.g. atxmega128a1 or
at32uc3a0256.
-v --verbose Verbose output (debug).
-h
--host <arg> Target host which runs the backend process.
-p
--port <arg> Specify which port to use for the backend
process. Ignored if the host option is not given.
-f --force
Force command even if firmware is not up to date.
-cl --clock
<arg> The frequency to use for communication with a device
(hz, khz, mhz, default hz). E.g. -cl 10mhz
-mb --max-baudrate <arg>
The maximum baud rate for communication on awire (Kbps).
-xr
--externalreset Apply external reset when starting a session.
-dc
--daisychain <args,..> Set up a JTAG daisychain. Arguments are
<devices-before devices-after instr-before instr-after>.
-sa
--snippet_addr <arg> Address where flash programming ram snippet
should be loaded.
-nr --no_ram Do not use ram snippet to
program flash.
-tv --target-voltage <arg> Set the STK600 or STK500
target voltage (float value).
-a0 --aref0 <arg> Set the
STK600 Aref0 or STK500 aref generator voltage (float value).
-a1
--aref1 <arg> Set the STK600 Aref1 generator voltage
(float value).
-cg --clock-generator <arg> Set the STK600 or
STK500 clock generator frequency (hz, khz, mhz, default hz).
--timeout <arg> Set the timeout value in seconds for commands.
The default is 180 seconds. Set to 0 for no timeout.
-q --quiet
Do not display activity indicator.
-? --help Display help
information.
-V --version Display version information.
chiperase Full erase of
chip.
erase Erase the
specified memory.
help
Displays help for a specific command.
info Display information about a
device.
interactive Run in
interactive mode.
list
Detect and print information about connected Atmel Tools.
program
Program device with data from <file>.
read
Read the contents of the memory on the device.
reset
Reset all domains and jump to the reset vector.
secure
Set the security bit on UC3 and ARM devices.
verify
Verify content of memory based on a file.
version
Display the version.
write
Write to the memory with values entered on the command line.
Use atprogram help <command> to get available attributes.
atprogram -t jtagice3 -i jtag
-d at32uc3b0512 program -f
e:\file.elf
atprogram -t avrone -i pdi -d atxmega128a1
chiperase
atprogram -t jtagicemkii -i jtag -d at90can128 info
For command specific help, use atprogram help <command>
C:\Program Files\Atmel\Atmel Studio 6.1\atbackend>atprogram help program
Usage:
atprogram [options] program
<arguments>
Information:
Program device with data from <file>. File format is determined
from its suffix unless specified.
If no
address space name is specified, flash is assumed for
Tiny/Mega and XMega, base for uc3 and
SAM.
Options:
Execute atprogram without arguments to list available
options.
Arguments:
-fl
--flash Program flash
address space. tinyAVR, megaAVR and AVR XMEGA
only.
-ee --eeprom
Program eeprom address space.
-us --usersignature Program user
signature.
-up --userpage
Program userpage.
-fs
--fuses Program
fuses.
-lb --lockbits
Program lockbits.
-f --file
(file) File to be programmed. Intel hex, elf
or binary.
-o --offset
(offset) Input file contents will be written to
this offset. Default offset is 0. Only valid
for binary file format.
--format
(format) Specify the format of file. Supported
input formats are ‘elf‘, ‘hex‘ and
‘bin‘.
-c --chiperase
Perform a chip erase before
programming.
-e --erase
Erase only affected pages before
programming. AVR UC3 and AVR XMEGA only. SAM devices
will always do this.
--verify Verify
memory after programming.
-l --list
List content of
file.
Examples:
atprogram -t avrone -i jtag -d atmega2560 program -c -fl -f
source.elf
Perform chiperase and program
only the segments of source.elf that map to flash.
atprogram -t avrone -i jtag -d
at32uc3a0512 program -e --verify -f source.elf
Erase only affected pages, program all segments in source.elf and
verify.
atprogram -t samice -i jtag -d atsam3s4c program -lb -f
lockbits.bin
Program lockbits as contained
in a binary file.
atprogram.exe : Atmel Studio Command Line Interface,布布扣,bubuko.com
atprogram.exe : Atmel Studio Command Line Interface
原文：http://www.cnblogs.com/shangdawei/p/3617031.html